Solid walls lose heat quickly and run cold on the inside, so insulating them is tempting. It also changes how the wall handles moisture, which is why damp and mould sometimes show up after the work. Check these things before you sign a quote.

Quick answer

Fix any existing damp, gutters, pointing and roof problems first, because the Energy Saving Trust says wall insulation cannot be fitted over damp and may trap it. Then ask the installer how moisture and ventilation will be handled. Older solid walls rely on permeable materials, and air bricks, wall vents and trickle vents must not be blocked.

Check this first

  1. Confirm the walls are solid. The Energy Saving Trust says an alternating brick pattern, with some bricks showing their short end, suggests a solid wall, and homes built before 1920 are more likely to be solid. A brick wall narrower than about 260mm is probably solid. If the walls are rendered or clad, ask a building professional.
  2. Fix the outside first. Repair damaged brickwork or pointing, roofs and overhangs, and gutters and downpipes. The Energy Saving Trust says skipping this can trap damp or make the insulation fail.
  3. Settle any existing damp. The Energy Saving Trust says wall insulation cannot be installed before existing damp problems are resolved. A patch that follows rain, or a damp band low on a wall, needs diagnosing first. See our guide to rising, penetrating and condensation damp.
  4. Ask about exposure, flooding and condition. The Energy Saving Trust says solid wall insulation may not suit homes exposed to extreme weather or flooding, or in poor condition, and installers should also check for a risk of overheating.
  5. Ask how moisture will be managed. The Energy Saving Trust says traditional materials such as brick, stone, timber and lime usually handle moisture well, and that insulation can change this. Internal insulation can make the outer wall colder so moisture may build up inside it. Ask which permeable materials and finishes are proposed and why.
  6. Ask about ventilation. The installer should not block or seal air bricks, underfloor grilles, wall vents or trickle vents, and should assess whether extractor fans or other ventilation are needed. Only then think about a dehumidifier, as the last rung.

What you find, and what to do

What you findLikely causeWhat to do
Damp patch or mould on a wall you plan to insulateCondensation, a leak or water getting in from outsideFind and fix the cause first. Insulation does not cure it. Not a dehumidifier job if it is a leak.
Quote says nothing about ventilation or air bricksGap in the proposalAsk the installer to explain how ventilation will be kept and whether more is needed.
Quote uses materials you cannot explainUnclear moisture designAsk why they suit an older solid wall, and get a second opinion from an experienced professional.
Damp or mould appears after the workInstallation, ventilation or an unrelated cause such as maintenanceContact the installer first and check your guarantee. A surveyor can give an independent view.
Listed home or conservation areaExtra rules applySeek advice and check permission with your local planning department before any work.
In Canterbury and the villages around it. We do not have Canterbury-specific figures on solid wall insulation and damp, and will not invent any. What matters is your own wall: its type, its condition and what is done to it. If your home is listed or in a conservation area, check with Canterbury City Council planning before you commit. Local help: Waltham and Petham.
When a dehumidifier is not the answer. A dehumidifier does not repair pointing, mend a gutter or stop water crossing a wall, and it does not remove mould that is already growing. Fix the water source first. Rented homes are not suitable unless the landlord authorises the changes, and a home with no loft cannot take a loft-mounted unit.

Where a Dryzen system fits. Once walls are sound and ventilation is sorted, an owner-occupied home with a loft may still carry too much everyday moisture. A Dryzen system is loft-mounted, with insulated ductwork to the central area or stairway only, and an adjustable ratio of fresh and recycled air, both dehumidified and filtered. Each unit covers 150 square metres and extracts 12 litres a day, at about 20 pounds a year in energy, and it helps stop the conditions mould and dust mites need. Ask for a free survey and we will say honestly whether it would help.

Common questions

Does solid wall insulation cause damp?

Not by itself, but it changes how moisture behaves. The Energy Saving Trust says insulation may trap moisture or reduce ventilation through the wall, so the installer must choose suitable permeable materials and check ventilation. Damp that is already there must be fixed before the work, because insulation cannot be installed over it.

Can I insulate an older or listed home?

Often yes, where it is appropriate, but get professional advice first. The Energy Saving Trust says listed buildings and homes in conservation areas need particular care and some insulation options need permission, so check with your local planning department.

Who do I contact if damp appears after wall insulation?

The Energy Saving Trust advises going back to the installer first. A registered installer should guarantee the work for 25 years, so check your paperwork. If the work was done under the ECO4 or GBIS schemes, TrustMark is offering free audits and says it will arrange fixes for any problems found.

Planning wall insulation?

Book a free survey and we will tell you honestly whether the damp is condensation or something that needs fixing first.

Book a Free Survey

Keep reading

Sources: Energy Saving Trust, Solid wall insulation.

Ready to Solve Your Home's Damp Problem?

Book your free, no-obligation survey today. Our specialist will assess your home and give you an honest recommendation.

Book Your Free Survey