If mould keeps coming back to one corner, one stretch of ceiling or the wall behind a wardrobe, the room's humidity is only half the story. The other half is a surface that is colder than its neighbours.

Quick answer

A cold spot is a patch of inside surface that stays colder than the rest, so moist indoor air condenses there first. Cold bridging is a cold path through the building, such as a lintel, a corner or a gap in insulation, that creates those patches. Find the pattern, rule out leaks, keep furniture off cold walls and heat steadily. Then reduce the moisture that settles on the cold patch.

Check this first

  1. Map where the mould sits. Corners, the strip above a window, the top of an outside wall and the back of a wardrobe are the classic cold-spot places. Mould in a neat patch with a defined edge points to a cold surface rather than a general damp problem.
  2. Feel the wall. On a cold morning, rest the back of your hand on the affected patch, then on the wall a metre away. A clear difference means a cold spot.
  3. Pull furniture away. GOV.UK guidance stresses leaving a gap between furniture and external walls. A wardrobe pushed hard against an outside wall traps cold, still air behind it.
  4. Look at the radiators. GOV.UK guidance notes that radiators on external walls and under windows give the best heat distribution. A room heated only for a short burst leaves outside walls cold.
  5. Check for a leak first. Look outside for damaged or blocked gutters and downpipes, cracked render and missing roof finishes. Water coming in from outside is penetrating damp, which a repair fixes.
  6. Think about what changed. GOV.UK guidance says homes that are insufficiently insulated and heated are more prone to condensation on the inside of external walls and windows. A patch that started after new windows, redecorating or a change in heating habits tells you where to look.

What you find, and what to do

What you findLikely causeWhat to do
Defined patch of mould in a room corner or behind furnitureCold spot with moist air held against itMove furniture out, heat the room steadily, ventilate when cooking and bathing, clean the mould off.
Strip of mould above a window or along a lintelCold bridge through the wall structureImprove heating and ventilation. Insulation fixes belong to a qualified installer.
Tide-mark or stain that follows rain or sits under a gutterLeak or blocked gutterRepair it. Not a dehumidifier job.
Damp low on the wall with salts or flaking plasterPossible rising dampSpecialist survey. Not a dehumidifier job.
Several cold, moist rooms with no leakMoisture building up on cold surfacesWork through the checks above, then consider humidity control.

Clean any mould that has formed. GOV.UK guidance says mould can be removed from hard surfaces with an appropriate cleaning product and should be left to dry completely. Soft, absorbent materials that have become mouldy may have to be thrown away. If you can smell mould but see none, the guidance notes it may be growing behind a surface such as wallpaper or carpet, which needs proper investigation. The WHO indoor air guidelines say that preventing persistent dampness and microbial growth on interior surfaces is the most important way to protect health, which is why fixing the cause matters more than repeated cleaning.

In Canterbury and the villages around it. Homes here range from older solid-walled houses to newer estates, and the same cold-spot pattern can turn up in either. In village homes such as those in Sturry and Bridge, start with the checks above on your own walls before assuming a cause. If your home is listed or in a conservation area, check with the council before changing walls or windows, and see our guide to damp in old and listed homes.
When a dehumidifier is not the answer. Leaks, blocked gutters, rising damp and flood or groundwater water need repair or a specialist, not equipment. A cold wall also needs better heating or insulation, which a dehumidifier does not provide. A Dryzen unit is mounted in the loft, so a home with no usable loft is not a candidate, and rented homes are not suitable unless the landlord authorises the changes.

Where a Dryzen system fits. It suits condensation-type damp in an owner-occupied home with a loft to mount the unit in. It helps reduce the moisture that condenses on cold surfaces, with a humidity target of 50 to 55 per cent. One unit covers 150 m2 and extracts 12 litres a day, and the smart app shows temperature and humidity. It does not warm a cold wall, repair leaks or treat rising damp.

Common questions

What is a cold spot on a wall?

It is a patch of inside wall or ceiling that stays colder than the surrounding surface, often because insulation is thin or missing there. Moist indoor air condenses on the cold patch first, which is why mould shows up there.

Is cold bridging the same as a leak?

No. A leak brings water in from outside and a repair is the fix. Cold bridging is a cold path through the structure that lets condensation form on the inside surface. Check for leaks first.

Will a dehumidifier fix a cold spot?

It helps reduce the moisture that condenses on cold surfaces, but it does not warm the wall. The cold spot itself is a heating or insulation question, so look at the causes first and treat humidity as one part of the answer.

Not sure what is causing yours?

Book a free survey and we will tell you honestly whether it is condensation or something else, even if that means we are not the right fix.

Book a Free Survey

Keep reading

Sources: GOV.UK, Understanding and addressing the health risks of damp and mould in the home; WHO, Guidelines for Indoor Air Quality: Dampness and Mould.

Ready to Solve Your Home's Damp Problem?

Book your free, no-obligation survey today. Our specialist will assess your home and give you an honest recommendation.

Book Your Free Survey